Tyco Electronics Computer Monitor B1ET 1215L User Manual

Touchmonitor User Guide  
1215L 12¨ LCD Desktop Touchmonitor  
1000 Series  
 
Copyright © 2008 Tyco Electronics. All Rights Reserved.  
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval  
system, or translated into any language or computer language, in any form or by any means,  
including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise with-  
out prior written permission of Elo TouchSystems.  
Disclaimer  
The information in this document is subject to change without notice. Elo TouchSystems makes no  
representations or warranties with respect to the contents hereof, and specifically disclaims any  
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems re-  
serves the right to revise this publication and to make changes from time to time in the content  
hereof without obligation of Elo TouchSystems to notify any person of such revisions or changes.  
Trademark Acknowledgments  
IntelliTouch, SecureTouch, AccuTouch, and MonitorMouse are trademarks of Elo TouchSystems.  
Other product names mentioned herein may be trademarks or registered trademarks of their  
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.  
iii  
 
Table of Contents  
Chapter 1  
Regulatory Information  
33  
37  
Introduction  
7
Warranty  
Index  
Product Description ...................................................7  
Precautions ................................................................7  
39  
Chapter 2  
Installation and Setup .................................... 9  
Unpacking Your Touchmonitor...................................9  
Product Overview ......................................................10  
Main Unit ..............................................................10  
Rear View ............................................................10  
Touch Interface Connection .......................................11  
Installing the Driver Software .....................................12  
Installing the Serial Touch Driver .........................13  
Installing the Serial Touch Driver for Windows  
XP, Windows 2000, Me, 95/98 and NT 4.0 .....13  
Installing the Serial Touch Driver for MS-DOS  
and Windows 3.1..................................................14  
Installing the USB Touch Driver ...........................15  
Installing the USB Touch Driver for Windows  
XP, Windows 2000, Me, 95/98 and NT 4.0 .....15  
Chapter 3  
Operation  
17  
About Touchmonitor Adjustments ..............................17  
Front Panel Controls ............................................18  
Controls and Adjustment ............................................19  
OSD Menu Functions ..........................................19  
OSD Control Options ...........................................20  
Preset Modes .......................................................21  
Power Management System ................................22  
Display Angle .............................................................22  
Chapter 4  
Troubleshooting  
23  
Solutions to Common Problems .................................23  
Appendix A.................................................... 25  
Appendix B  
Care and Handling of Your Touchmonitor ..................28  
Appendix C  
Touchmonitor Specifications ......................................30  
AccuTouch Touchscreen Specifications .............31  
12" LCD Touchmonitor (ET1215L-XXWA-1-G)  
Dimensions .........................................................32  
v
 
CHAPTER  
1
INTRODUCTION  
Product Description  
Your new touchmonitor combines the reliable performance of touch technology with the latest  
advances in LCD display design. This combination of features creates a natural flow of information  
between a user and your touchmonitor.  
This LCD monitor incorporates 12” color active matrix thin-film-transistor (TFT) liquid crystal  
display to provide superior display performance. A maximum resolution of SVGA800x600 is ideal  
for displaying graphics and images. Other outstanding designs that enhance this LCD monitor’s  
performance are Plug & Play compatibility, and OSD (On Screen Display) controls.  
NOTE  
Some monitors do not have the touchscreen capability.  
Precautions  
Follow all warnings, precautions and maintenance as recommended in this user’s manual to  
maximize the life of your unit. See Appendix B for more information on touchmonitor safety.  
1-7  
 
About the Product  
Your LCDDesktop Touchmonitor is a 12” SVGATFT color display with the following features:  
• The internal microprocessor digitally controls auto-scanning. For horizontal scan frequencies  
between 31.5 KHz and 48 KHz, and vertical scan frequencies between 56.3 Hz and 75.0 Hz. In  
each frequency mode, the microprocessor-based circuitry allows the monitor to function at the  
precision-of a fixed frequency.  
• High contrast color TFT LCD display support resolution up to SVGA 800x600. Compatible with  
VGA, SVGA(non-interlaced) and most Macintosh compatible color video cards.  
• Power management system conforms to VESADPMS standard.  
• Supports DDC1/2B for Plug & Play compatibility.  
• Advanced OSDcontrol for picture quality adjustment.  
• Detachable stand for wall-mounting application.  
• Optional touch screen function.  
For full Product Specifications refer to Appendix C.  
1-8 User Guide  
 
CHAPTER  
2
INSTALLATION AND SETUP  
This chapter discusses how to install your LCDtouchmonitor and how to install the driver software.  
Unpacking Your Touchmonitor  
Check that the following 8 items are present and in good condition:  
LCD monitor  
VGAcable  
USB cable  
Serial Cable  
European power cable  
Power cable US/Canada  
Elo QuickStatr  
CD  
Software  
CDand Quick InstallGuide  
2-9  
 
Touch Interface Connection  
Note: Before connecting the cables to your touchmonitor and PC, be sure that the computer  
and  
touchmonitor are turned off.  
1. Connect one end of the power cord to the monitor and the other end to the outlet.  
2. Connect one end of either the touchscreen serial(RS232) cable or the touch screen USB cable  
(but not both) to the rear side of the computer and the other end to the LCD monitor. Tighten by  
turning the two thumb screws clockwise to ensure proper grounding(optional module USB cable  
does not have thumb screws)  
3. Connect one end of the video cable to the rear side of computer and the other to the LCDmonitor.  
Tighten by turning the two thumb screws clockwise to ensure proper grounding.  
4. Press the power button on the front panel to turn the monitor power on.  
2-10 User Guide  
 
Product Overview  
Main Unit  
Rear View  
2-11  
 
Installing the Driver Software  
Elo TouchSystems provides driver software that allows your touchmonitor to work with your  
computer. Drivers are located on the enclosed CD-ROM for the following operating systems:  
• Windows XP  
• Windows 2000  
• Windows Me  
• Windows 98  
• Windows 95  
• WindowsNT 4.0  
Additional drivers and driver information for other operating systems are available on the Elo  
Your Elo touchmonitor is plug-and-play compliant. Information on the video capabilities of your  
touchmonitor is sent to your video display adapter when Windows starts. If Windows detects your  
touchmonitor, follow the instructions on the screen to install a generic plug-and-play monitor.  
Refer to the appropriate following section for driver installation instructions.  
Depending upon whether you connected the serial communication cable or the USB  
communication cable, you should install only the serial driver or the USB driver.  
2-12 User Guide  
 
Installing the Serial Touch Driver  
Installing the Serial Touch Driver for Windows XP,  
Windows 2000, Me, 95/98 and NT4.0  
NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install  
the driver.  
1 Insert the Elo CD-ROM in your computer's CD-ROM drive.  
2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the  
CD and starts the setup program.  
3 Follow the directions on the screen to complete the driver setup for your version of Windows.  
4 If the AutoStart feature is not active:  
5 Click Start > Run.  
6 Click the Browse button to locate the EloCd.exe program on the CD-ROM.  
7 Click Open, then OK to run EloCd.exe.  
8 Follow the directions on the screen to complete the driver setup for your version of Windows.  
To install Windows 2000 and Windows XP, you must use the "update driver" method; you will not  
find a setup.exe file within the download.  
2-13  
 
Installing the Serial Touch Driver for MS-DOS and Windows 3.1  
You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to  
continue using your mouse along with your touchmonitor inDOS.  
To install Windows 3.x and MS-DOS from Windows 95/98, follow the directions below:  
1 Insert the CD-ROM in your computer’s CD-ROM drive.  
2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your  
CD- ROM drive may be mapped to a different drive letter).  
3 Type install and press Enter to start the installation.  
4 Align the touchscreen.  
You must have already completed Steps 1 and 2 before proceeding.  
To run the INSTALLprogram:  
1 Type INSTALL at the DOS prompt in the directory containing the driver install files.  
2 INSTALL asks you to select the software to install. Then choose d:\EloDos_W31 from the  
displayed list.  
3 INSTALL also asks you for the paths to use during installation, or you may use its defaults.  
INSTALL creates directories as necessary, and warns you if they exist.  
If you are updating your software, you may wish to specify the paths containing the earlier versions,  
and overwrite the obsolete files. All executable programs are upward compatible. For a list of  
differences from each previous version of the drivers, be sure to select "Differences from Previous  
Versions" during the installation process.  
INSTALLupdates yourAUTOEXEC.BAT file with the drivers you select. INSTALLmakes a copy  
of your originalAUTOEXEC.BAT file, calledAUTOEXEC.OLD. If you already have Elo driver  
commands in your AUTOEXEC.BAT file, they will be commented out.  
When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory you specified. GO  
loads the touchscreen driver, runs the calibration program ELOCALIB, and gives you some final  
instructions.  
If you are using Windows 3.1, you will also calibrate the touchscreen within Windows 3.1 with the  
Touchscreen Control Panel.  
2-14 User Guide  
 
Installing the USB Touch Driver  
Installing the USB Touch Driver for Windows XP,  
Windows 2000, Me, 95/98 and NT4.0  
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.  
If Windows 98, Windows Me or Windows 2000 starts theAdd New Hardware Wizard:  
2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose  
Next.  
3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use  
Browse to select the \EloUSB directory on the Elo CD-ROM.  
4 Choose Next. Once the Elo USB touchscreen driver has been detected, choose Next again.  
5 You will see several files being copied. Insert your Windows 98 CDif prompted. Choose Finish.  
If Windows 98, Windows Me or Windows 2000 does not start the Add New Hardware Wizard:  
NOTE:  
For Windows 2000 you must have administrator access rights to install the driver.  
1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. If the AutoStart feature for your  
CD-ROM drive is active, the system automatically detects the CD and starts the setup program.  
2 Follow the directions on the screen to complete the driver setup for your  
version of Windows.  
If the AutoStart feature is not active:  
1 Click Start > Run.  
2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.  
3 Click Open, then OK to run EloCd.exe.  
4 Follow the directions on the screen to complete the driver setup for your version of Windows.  
To install Windows 2000 and Windows XP, you must use the "update driver" method; you will not  
find a setup.exe file within the download.  
2-15  
 
2-16 User Guide  
 
CHAPTER  
3
OPERATION  
About Touchmonitor Adjustments  
Your touchmonitor will unlikely require adjustment. Variations in video output and application may  
require adjustments to your touchmonitor to optimize the quality of the display.  
For best performance, your touchmonitor should be operating in native resolution, that is 800 x 600  
at 60k-75 Hz. Use the Display control panel in Windows to choose 800 x 600 resolution.  
Operating in other resolutions will degrade video performance. For further information, please  
refer toAppendix A.  
All adjustments you make to the controls are automatically memorized. This feature saves you from  
having to reset your choices every time you unplug or power your touchmonitor off and on. If there  
is a power failure, your touchmonitor settings will not default to the factory specifications.  
3-17  
 
Front Panel Controls  
1
2
3
4
5
Control  
1 Menu/Exit  
2
Function  
Display/Exits the OSD menus.  
1. Enter contrast of the OSD.  
2. Increase value of the adjustment item.  
3. Select item.  
3
1. Enter brightness adjustment.  
2. Decrease value of the adjustment item.  
3. Select item counter-clockwise.  
Selects the adjustment items from the OSD menus.  
Switches the power of the monitor.  
4 Select  
5 Power Switch  
3-18 User Guide  
 
Controls and Adjustment  
OSD Menu Functions  
To Display and Select the OSD Functions:  
1 Press the Menu key to activate the OSD menu.  
2 Use or to move clockwise or counterclockwise through the menu. Press the Enter key,  
the parameter will be highlighted when selected.  
3 To quit the OSD screen at any time during the operation, press the Menu key. If no keys are  
pressed for a short time period, the OSD automatically disappears.  
NOTE:  
The OSD screen will disappear if no input activities are detected for 45 seconds.  
3-19  
 
OSD Control Options  
Control  
Description  
Brightness  
Contrast  
H-Position  
V-Position  
Phase  
Increases or decreases brightness  
Increases or decreases contrast  
Moves the screen left or right  
Moves the screen up or down  
Increases or decreases the snow noise of the image after auto  
adjustment is made.  
Clock  
The dot clock is fine-adjusted after auto adjust.  
Moves the OSD position horizontally on the screen. When the  
button is pressed, the OSD control menu will move to the right  
side of the screen. Likewise, when the button is pressed, the  
OSD control menu will move to the left side.  
OSD H-Position  
OSD V-Position  
Moves the OSD position vertically on the screen. When the  
button is pressed, the OSD control menu will move to the top side  
of the screen. Likewise, when the button is pressed, the OSD  
control menu will move to the lower side.  
Color Balance  
Auto-Adjust  
Press or to select 9300, 6500, 5500, 7500 and USER. Only when  
selecting USER can you make adjustments to the R/G/B content.  
Press Enter to restore to factory default setting.  
PressAuto to enable this function. TheAuto-Adjust will automatically  
adjust V-Position, H-Position, Clock and Clock-Phase.  
Returns the monitor to its default settings.  
Recall Defaults  
OSDLanguage  
Select from English, French, German ,Spanish and Japanese.  
Information Description Indicates the current resolution, H-Frequency and V-Frequency.  
3-20 User Guide  
 
Preset Modes  
To reduce the need for adjustment for different modes, the monitor has default setting modes that  
are most commonly used as given in the table below. If any of these display modes are detected, the  
monitor automatically adjusts the picture size and centering. When none of the mode is matched,  
the user can store their preferred modes in the user modes. The monitor is capable of storing up to  
7 user modes. The only condition to store as a user mode is the new display information must have  
1 KHz difference for horizontal frequency or 1 Hz for vertical frequency or the sync signal  
polarities are different from the default modes.  
H. Freq.  
(KHz)  
Band Width  
(MHz)  
Mode Resolution  
H
V
1
VGA 640 x 35070 Hz  
31.47  
31.47  
31.47  
35.00  
37.86  
37.50  
35.16  
37.88  
46.88  
48.08  
28.322  
28.322  
25.175  
32.24  
31.5  
31.5  
36  
2
VGA 720 x 40070 Hz  
VGA 640 x 48060 Hz  
MAC 640 x 48066 Hz  
VESA 640 x 480 72 Hz  
VESA 640 x 480 75 Hz  
VESA 800 x 600 56 Hz  
VESA 800 x 600 60 Hz  
VESA 800 x 600 75 Hz  
VESA 800 x 600 72 Hz  
3
4
-
-
-
-
5
6
-
-
7
+
+
+
+
+
+
+
+
8
40  
9
49.5  
50  
10  
3-21  
 
Power Management System  
The monitor is equipped with the power management function which automatically reduces the power  
consumption when not in use.  
Power  
Mode  
On  
Consumption  
<20W  
Sleep  
Off  
<4W  
<2W  
We recommend switching the monitor off when it is not in use for a long time.  
NOTE:  
The monitor automatically goes through the Power Management System (PMS) steps  
when it is idle. To release the monitor from PMS condition, press any key on the keyboard  
or move mouse.  
Display Angle  
For viewing clarity, you can tilt the LCDforward (up to -5 degrees) or backward (up to 90 degrees.)  
CAUTION In order to protect the LCD, be sure to hold the base when adjusting the LCD,  
and take care not to touch the screen.  
3-22 User Guide  
 
CHAPTER  
4
TROUBLESHOOTING  
If you are experiencing trouble with your touchmonitor, refer to the following table. If the problem  
persists, please contact your local dealer or our service center.  
Solutions to Common Problems  
Problem  
Suggestion(s)  
The monitor does not respond  
after you turn on the system.  
Check that the monitor’s Power Switch is on.  
Turn off the power and check the monitor’s power cord  
and signal cable for proper connection.  
Characters on the screen are dim  
The screen is blank  
Refer to the About Touchmonitor Adjustments section to  
adjust the brightness.  
During operation, the monitor screen may automatically turn  
off as a result of the Power Saving feature. Press any key to see  
if the screen reappears.  
Refer to the About Touchmonitor Adjustments section to  
adjust the brightness.  
Screen flashes when initialized  
“Out of Range” display  
Turn the monitor off then turn it on again.  
Check to see if the resolution of your computer is higher than  
that of the LCD display.  
Reconfigure the resolution of your computer to make it less  
than or equal to 800x600. See Appendix A for more information  
on resolution.  
Touch doesn’t work  
Make sure the touch cable is securely attached at both ends.  
4-23  
 
4-24 User Guide  
 
APPENDIX  
A
NATIVE RESOLUTION  
The native resolution of a monitor is the resolution level at which the LCD panel is designed to  
perform best. For the LCD touchmonitor, the native resolution is 800 x 600 for the 12 inch size. In  
almost all cases, screen images look best when viewed at their native resolution. You can lower the  
resolution setting of a monitor but not increase it.  
Input Video  
12" LCD  
640x480 (VGA)  
800x600 (SVGA)  
Transforms input format to 800x600  
Displays in Native Resolution  
The native resolution of an LCD is the actual number of pixels horizontally in the LCD by the  
number of pixels vertically in the LCD. LCD resolution is usually represented by the  
following symbols:  
VGA  
640x480  
SVGA  
XGA  
800x600  
1024x768  
1280x1024  
1600x1200  
SXGA  
UXGA  
A-25  
 
As an example, a SVGA resolution LCD panel has 800 pixels horizontally by 600 pixels vertically.  
Input video is also represented by the same terms. XGA input video has a format of 1024 pixels  
horizontally by 768 pixels vertically. When the input pixels contained in the video input format  
match the native resolution of the panel, there is a one to one correspondence of mapping of input  
video pixels to LCDpixels. As an example, the pixel in column 45 and row 26 of the input video is in  
column 45 and row 26 of the LCD. For the case when the input video is at a lower resolution than the  
native resolution of the LCD, the direct correspondence between the video pixels and the LCD  
pixels is lost. The LCD controller can compute the correspondence between video pixels and LCD  
pixels using algorithms contained on its controller. The accuracy of the algorithms determines the  
fidelity of conversion of video pixels to LCD pixels. Poor fidelity conversion can result in artifacts  
in the LCDdisplayed image such as varying width characters.  
A-26 User Guide  
 
APPENDIX  
B
TOUCHMONITOR SAFETY  
This manual contains information that is important for the proper setup and maintenance of your  
touchmonitor. Before setting up and powering on your new touchmonitor, read through this manual,  
especially Chapter 2 (Installation), and Chapter 3 (Operation).  
1 To reduce the risk of electric shock, follow all safety notices and never open the touchmonitor  
case.  
2 Turn off the product before cleaning.  
3 Your new touchmonitor is equipped with a 3-wire, grounding power cord. The power cord plug  
will only fit into a grounded outlet. Do not attempt to fit the plug into an outlet that has not been  
configured for this purpose. Do not use a damaged power cord. Use only the power cord that  
comes with your touchmonitor. Use of an unauthorized power cord may invalidate your warranty.  
4 The slots located on the sides and top of the touchmonitor case are for ventilation. Do not block  
or insert anything inside the ventilation slots.  
5 It is important that your touchmonitor remains dry. Do not pour liquid into or onto your  
touchmonitor. If your touchmonitor becomes wet do not attempt to repair it yourself.  
B-27  
 
Care and Handling of Your Touchmonitor  
The following tips will help keep your touchmonitor functioning at the optimal level.  
• To avoid risk of electric shock, do not disassemble the brick supply or display unit cabinet. The  
unit is not user serviceable. Remember to unplug the display unit from the power outlet before  
cleaning.  
• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do not use thinner or  
benzene, abrasive cleaners or compressed air.  
• To clean the display unit cabinet, use a cloth lightly dampened with a mild detergent.  
• Avoid getting liquids inside your touchmonitor. If liquid does get inside, have a qualified service  
technician check it before you power it on again.  
• Do not wipe the screen with a cloth or sponge that could scratch the surface.  
• To clean the touchscreen, use window or glass cleaner. Put the cleaner on the rag and wipe the  
touchscreen. Never apply the cleaner directly on the touchscreen.  
Warning  
This product consists of devices that may contain mercury, which must be recycled or disposed  
of in accordance with local, state, or federal laws. (Within this system, the backlight lamps in the  
monitor display contain mercury.)  
Waste Electrical and Electronic Equipment(WEEE) Directive  
In the European Union, this label indicates that this product should not be disposed of with  
household waste. It should be deposited at an appropriate facility to enable recovery and recycling.  
B-28 User Guide  
 
APPENDIX  
C
TECHNICAL SPECIFICATIONS  
C-29  
 
Touchmonitor Specifications  
Model  
ET1215L  
LCDDisplay  
Display Size  
Pixel Pitch  
Display Mode  
12” TFTActive Matrix Panel  
246(H) x 184.5(V) mm  
0.3075(H) x 0.3075(V) mm  
VGA 640 x 350 (70Hz)  
VGA 720 x 400 (70Hz)  
VGA 640 x 480 (60 / 72/ 75Hz)  
SVGA 800 x 600 (56 / 60 / 72/ 75Hz) Maximum  
500 : 1 (typical)  
Non Touch: typical 200 Cd/m2 ; Min 160 Cd/m2  
AccuTouch: typical 164 Cd/m2 ; Min 131 Cd/m2  
IntelliTouch: typical 184 Cd/m2 ; Min 147 Cd/m2  
Capacitive: typical 170 Cd/m2 ; Min 136 Cd/m2  
Tr: 10 ms Tf: 25ms (Typ.)  
Max. Resolution  
Contrast Ratio  
Brightness  
Response Time  
Display Color  
Viewing Angle  
262K  
Vertical -45o ~ +50o  
Horizontal -70o ~+70o  
Input Signal  
Video  
Sync  
R.G.B. Analog 0.7Vp-p, 75 ohm  
TTL Positive orNegative  
Signal Connector  
Front Control  
OSD  
MiniD-Sub 15 pin  
Menu,  
,
, Select, Power  
Contrast, Brightness, H-Position, V-Position,  
Color Temperature, Phase, Clock, OSDTime, Recall,  
Language: English, French, German, Spanish, Japanese  
DDC1 / 2B  
Plug & Play  
Touch Panel (optional)  
PowerAdapter  
AccuTouch /IntelliTouch/Capacitive  
Input AC 100-240V, 50/60Hz  
0oC ~ 40oC (32oF ~ 104oF)  
Operating Conditions  
Temperature  
Humidity  
20% ~ 80% (No Condensation)  
To 12,000 Feet  
Altitude  
Storage Conditions  
Temperature  
Humidity  
-20oC ~ 60oC (-4oF ~ 140oF)  
10% ~ 90% (No Condensation)  
301 x 285 x 168mm  
Dimensions (HxWxD)  
Weight (Net)  
3.8Kg  
Certifications  
TUV, UL, C-UL, FCC-B, CE, VCCI, C-Tick, MPRII  
C-30 User Guide  
 
AccuTouch Touchscreen Specifications  
Mechanical  
Construction  
Top: Polyester with outside hard-surface coating with clear or antiglare finish.  
Inside: Transparent conductive coating.  
Bottom: Glass substrate with uniform resistive coating. Top and bottom layers  
separated by patented separator dots.  
Positional Accuracy  
Touchpoint Density  
Standard deviation of error is less than 0.080 in. (2.03 mm). This equates to less  
than ±1%.  
More than 100,000 touchpoints/in2 (15,500 touchpoints/cm2).  
Touch Activation Force Typically less than 4 ounces (113 grams).  
Surface Durability  
Meets Taber Abrasion Test (ASTM D1044), CS-10F wheel, 500 g. Meets pencil  
hardness 3H.  
Expected Life  
Performance  
AccuTouch technology has been operationally tested to greater than 35 million  
touches in one location without failure, using a stylus similar to a finger.  
Optical  
Light Transmission  
(perASTMD1003)  
Visual Resolution  
Typically 85% at 550-nm wavelength (visible light spectrum).  
All measurements made using USAF 1951 Resolution Chart, under 30 X  
magnification, with test unit located approximately 1.5 in. (38 mm) from surface  
of resolution chart.  
Antiglare surface: 6:1 minimum.  
Haze (perASTM D1003) Antiglare surface: Less than 15%.  
Gloss (per ASTM D2457) Antiglare surface: 90 ± 20 gloss units tested on a hard-coated front surface.  
C-31  
 
12” LCD Touchmonitor (ET1215L-XXXA-1-G) Dimensions  
C-32 User Guide  
 
REGULATORY INFORMATION  
I. Electrical Safety Information:  
A) Compliance is required with respect to the voltage, frequency, and current requirements  
indicated on the manufacturer’s label. Connection to a different power source than those  
specified herein will likely result in improper operation, damage to the equipment or pose a fire  
hazard if the limitations are not followed.  
B) There are no operator serviceable parts inside this equipment. There are hazardous voltages  
generated by this equipment which constitute a safety hazard. Service should be provided only  
by a qualified service technician.  
C) This equipment is provided with a detachable power cord which has an integral safety ground  
wire intended for connection to a grounded safety outlet.  
1) Do not substitute the cord with other than the provided approved type. Under no  
circumstances use an adapter plug to connect to a 2-wire outlet as this will defeat the  
continuity of the grounding wire.  
2) The equipment requires the use of the ground wire as a part of the safety certification,  
modification or misuse can provide a shock hazard that can result in serious injury or  
death.  
3) Contact a qualified electrician or the manufacturer if there are questions about the  
installation prior to connecting the equipment to mains power.  
II. Emissions and Immunity Information  
A) Notice to Users in the United States: This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and  
used in accordance with the instructions, may cause harmful interference to radio  
communications.  
B) Notice to Users in Canada: This equipment complies with the Class B limits for radio noise  
emissions from digital apparatus as established by the Radio Interference Regulations of Industrie  
Canada.  
C) Notice to Users in the European Union: Use only the provided power cords and  
interconnecting cabling provided with the equipment. Substitution of provided cords and cabling  
may compromise electrical safety or CE Mark Certification for emissions or immunity as  
required by the following standards:  
33  
 
This Information Technology Equipment (ITE) is required to have a CE Mark on the  
manufacturer’s label which means that the equipment has been tested to the following Directives  
and Standards:  
This equipment has been tested to the requirements for the CE Mark as required by EMC  
Directive 89/336/EEC indicated in European Standard EN 55022 Class B and the Low Voltage  
Directive 73/23/EEC as indicated in European Standard EN 60950.  
D) General Information to all Users: This equipment generates, uses and can radiate radio  
frequency energy. If not installed and used according to this manual the equipment may cause  
interference with radio and television communications. There is, however, no guarantee that  
interference will not occur in any particular installation due to site-specific factors.  
1) In order to meet emission and immunity requirements, the user must observe the following:  
a) Use only the provided I/O cables to connect this digital device with any computer.  
b) To ensure compliance, use only the provided manufacturer’s approved line cord.  
c) The user is cautioned that changes or modifications to the equipment not expressly  
approved by the party responsible for compliance could void the user’s authority to operate  
the equipment.  
2) If this equipment appears to cause interference with radio or television reception, or any other  
device:  
a) Verify as an emission source by turning the equipment off and on.  
b) If you determine that this equipment is causing the interference, try to correct the  
interference by using one or more of the following measures:  
i) Move the digital device away from the affected receiver.  
ii) Reposition (turn) the digital device with respect to the affected receiver.  
iii) Reorient the affected receiver’s antenna.  
iv) Plug the digital device into a different AC outlet so the digital device and the  
receiver are on different branch circuits.  
v) Disconnect and remove any I/O cables that the digital device does not use.  
(Unterminated I/O cables are a potential source of high RF emission levels.)  
vi) Plug the digital device into only a grounded outlet receptacle. Do not use AC  
adapter plugs. (Removing or cutting the line cord ground may increase RF emission  
levels and may also present a lethal shock hazard to the user.)  
If you need additional help, consult your dealer, manufacturer, or an experienced radio or television  
technician.  
34 UserGuide  
 
EN60950-1  
MPR II  
N10051  
This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equip-  
ment Regulations.  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel  
brouilleur du Canada.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) This device must accept  
any interference reveived, including interference that may cause undesired operation.  
 
 
WARRANTY  
Except as otherwise stated herein or in an order acknowledgment delivered to Buyer, Seller warrants  
to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the  
touchmonitors and components of the product is 3 (three) years.  
Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time  
and from time to time make changes in the components delivered as Products or components.  
Buyer shall notify Seller in writing promptly (and in no case later than thirty (30) days after discovery)  
of the failure of any Product to conform to the warranty set forth above; shall describe in  
commercially reasonable detail in such notice the symptoms associated with such failure; and  
shall provide to Seller the opportunity to inspect such Products as installed, if possible. The  
notice must be received by Seller during the Warranty Period for such product, unless  
otherwise directed in writing by the Seller. Within thirty (30) days after submitting such notice,  
Buyer shall package the allegedly defective Product in its original shipping carton(s) or a  
functional equivalent and shall ship to Seller at Buyer’s expense and risk.  
Within a reasonable time after receipt of the allegedly defective Product and verification by  
Seller that the Product fails to meet the warranty set forth above, Seller shall correct such  
failure by, at Seller’s options, either (i) modifying or repairing the Product or (ii) replacing the  
Product. Such modification, repair, or replacement and the return shipment of the Product with  
minimum insurance to Buyer shall be at Seller’s expense. Buyer shall bear the risk of loss or  
damage in transit, and may insure the Product. Buyer shall reimburse Seller for transportation  
cost incurred for Product returned but not found by Seller to be defective. Modification or  
repair, of Products may, at Seller’s option, take place either at Seller’s facilities or at Buyer’s  
premises. If Seller is unable to modify, repair, or replace a Product to conform to the warranty  
set forth above, then Seller shall, at Seller’s option, either refund to Buyer or credit to Buyer’s  
account the purchase price of the Product less depreciation calculated on a straight-line basis  
over Seller’s stated Warranty Period.  
37  
 
THESE REMEDIES SHALL BE THE BUYER¡¦S EXCLUSIVE REMEDIES FOR BREACH OF  
WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, SELLER  
GRANTSNO OTHERWARRANTIES, EXPRESS OR IMPLIEDBYSTATUTE OR OTHERWISE,  
REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY,  
THEIR MERCHANTABILITY, THEIRNONINFRINGEMENT, OR OTHERWISE. NO  
EMPLOYEE OF SELLER OR ANY OTHER PARTY IS AUTHORIZEDTO MAKE ANY WAR-  
RANTYFORTHEGOODS OTHERTHANTHE WARRANTYSETFORTH HEREIN. SELLER’S  
LIABILITY UNDER THE WARRANTY SHALL BE LIMITEDTOAREFUNDOF THE  
PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL SELLER BE LIABLE FOR  
THE COST OF PROCUREMENT OR INSTALLATION OF SUBSTITUTE GOODS BY BUYER  
OR FORANY SPECIAL, CONSEQUENTIAL, INDIRECT, OR INCIDENTALDAMAGES.  
Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless from all  
liability relating to (i) assessing the suitability for Buyer’s intended use of the Products and of any  
system design or drawing and (ii) determining the compliance of Buyer’s use of the Products with  
applicable laws, regulations, codes, and standards. Buyer retains and accepts full responsibility for  
all warranty and other claims relating to or arising from Buyer’s products, which include or incorpo-  
rate Products or components manufactured or supplied by Seller. Buyer is solely responsible for  
any and all representations and warranties regarding the Products made or authorized by Buyer. Buyer  
will indemnify Seller and hold Seller harmless from any liability, claims, loss, cost, or expenses  
(including reasonable attorney’s fees) attributable to Buyer’s products or representations or  
warranties concerning same.  
38 User Guide  
 
INDEX  
Image, scrolling, 23  
Input Signal, 30  
Numerics  
12" LCD Touchmonitor (ET1215L-XXWA-1-G)  
Dimensions, 32  
Installation and Setup, 9  
Installing the Driver Software, 12  
Installing the Serial Touch Driver, 13  
Installing the Serial Touch Driver for MS-DOS and  
Windows 3.1, 14  
A
About the Product, 8  
Installing the Serial Touch Driver for Windows XP,  
Windows 2000, Me, 95/98 and NT 4.0, 13  
Installing the USB Touch Driver, 15  
Installing the USB Touch Driver for Windows XP,  
Windows 2000, Me, 95/98 and NT 4.0, 15  
About Touchmonitor Adjustments, 17  
AccuTouch Touchmonitor Specifications, 31  
B
Brightness, 30  
L
C
Light Transmission, AccuTouch, 31  
Care and Handling of Your Touchmonitor, 28  
Certifications, 30  
M
Cleaning Your Touchmonitor, 28  
Construction, AccuTouch, 31  
Contrast Ratio, 30  
Main Unit, 10  
Max. Resolution, 30  
Mechanical, AccuTouch, 31  
Controls and Adjustment, 19  
N
D
Native Resolution, 25  
Dimensions (HxWxD), 30  
Display Angle, 22  
Display Color, 30  
Display Mode, 30  
Display Size, 30  
O
Operating Conditions, 30  
Optical, AccuTouch, 31  
OSD, 30  
OSD Control Options, 20  
OSD Menu Functions, 19  
E
Electrical Safety Information, 33  
Emissions and Immunity Information, 33  
Expected Life Performance, AccuTouch, 31  
P
Pixel Pitch, 30  
Plug & Play, 30  
F
Positional Accuracy, AccuTouch, 31  
Power Adapter, 30  
Power Management System, 22  
Precautions, 7  
Front Control, 30  
Front Panel Controls, 18  
Product Description, 7  
Product Overview, 10  
G
Gloss, AccuTouch, 31  
R
H
Rear View, 10  
Haze, AccuTouch, 31  
Regulatory Information, 33  
Response Time, 30  
I
Image problem, 23  
I ND E X - 39  
 
S
V
Signal Connector, 30  
Solutions to Common Problems, 23  
Storage Conditions, 30  
Surface Durability, AccuTouch, 31  
SVGA, 25  
VGA, 25  
Viewing Angle, 30  
Visual Resolution, AccuTouch, 31  
W
Warranty, 37  
Weight (Net), 30  
T
Technical Specifications, 29  
Touch Activation Force, AccuTouch, 31  
Touch Interface Connection, 11  
Touch not working, 23  
Touch Panel (optional), 30  
Touchmonitor Safety, 27  
Touchmonitor Specifications, 30  
Touchpoint Density, AccuTouch, 31  
Troubleshooting, 23  
U
Unpacking Your Touchmonitor, 9  
UXGA, 25  
I N D E X - 40  
 
 
Check out Elo’s Web site!  
Get the latest...  
• Product information  
• Specifications  
• News on upcoming events  
• Press release  
• Software drivers  
• Touchmonitor Newsletter  
Getting in Touch with Elo  
To find out more about Elo’s extensive range of touch solutions, visit our Web site at www.elotouch.com or simply call the office  
nearest you:  
North America  
Elo TouchSystems  
301 Constitution Drive,  
Menlo Park, CA 94025  
USA  
Germany  
Belgium  
Asian-Pacific  
Tyco Electronics Raychem GmbH  
(Elo TouchSystems Division)  
Finsinger Feld 1  
Tyco Electronics Raychem GmbH  
(Elo TouchSystems Division)  
Diestsesteenweg 692  
B-3010 Kessel-Lo  
Sun Homada Bldg. 2F  
1-19-20 Shin-Yokohama  
Kanagawa 222-0033  
Japan  
D-85521 Ottobrunn  
Germany  
Belgium  
(800) ELO-TOUCH  
(800-356-8682)  
Tel +49(0)(89)60822-0  
Fax +49(0)(89)60822-180  
Tel +32(0)(16)35-2100  
Fax +32(o)(16)35-2101  
Tel +81(45)478-2161  
Fax +81(45)478-2180  
Tel 650-361-4800  
Fax 650-361-4722  
 

Texas Instruments Network Card 4Q 2006 User Manual
Tokina Camera Accessories TVR2714 User Manual
Toshiba Air Conditioner RAV SM1103UT E User Manual
Toshiba CRT Television 27AF41 User Manual
Toshiba Projector TDP T9 User Manual
Toto Plumbing Product TET2ANS 31 User Manual
Trane Heating System TR200 User Manual
Tricity Bendix Oven SIE 225 User Manual
Univex Flat Panel Television 26HF5545D User Manual
Velodyne Acoustics Home Theater System VMS 8 User Manual