Uniden Network Router 1868P User Manual

UIP 1868P Router Configuration Guide  
The UIP1868P can function as your primary gateway/router or as a client  
within an existing network configuration.  
In the menu bar down the left side of the  
screen, select WAN.  
If you currently have broadband access and a gateway/router installed at  
your location, you may add the UIP1868P as a client to your network. If  
you currently have broadband internet access and do not have a router,  
you may install your UIP1868P as the primary router to your network.  
In the top menu bar, select WAN Settings.This  
will open the Wan Configuration screen.  
(See Figure #7)  
Select the radio button labeled SPECIFY FIXED  
1 Installing the UIP1868P as a client in an existing network  
configuration/router  
WAN CONFIGURATION  
Figure #7  
Enter the IP Address, Subnet Mask, and Gateway Address provided by  
Computer  
your ISP  
Broadband  
modem  
Local router  
Internet  
Click SAVE WAN CONFIGURATION.  
UIP1868P  
When the utility displays a window telling you it must reboot the  
phone, make sure your broadband modem is connected to your  
phone's WAN port, then click OK.When the phone finishes rebooting,  
it will ask your broadband modem to assign an IP address.  
(See Figure #8)  
Plug one end of the enclosed Ethernet cable into the WAN port on the  
back of the UIP1868P. Plug the other end of the Ethernet cable into your  
router/gateway which is connected to your broadband modem.  
NOTE: For detailed installation with a Static IP  
address, please refer to the UIP1868P User  
Interface Guide – WAN Configuration section)  
2 Installing the UIP1868P as your primary gateway/router  
Figure #8  
You are now ready to activate your Packet8 account. (Please refer to  
the Uniden Quick Start Guide instructions for activating your Packet8  
account.)  
Broadband  
modem  
UIP1868P  
Computer  
Local switch  
or router  
Internet  
You can download a copy of the UIP1868P User Interface Guide at  
The UIP1868P supports the two most common broadband connection  
protocols: DHCP (most common connection type found with Cable  
Modem) and PPPoE (most DSL providers use this connection type).  
Setting up with DHCP  
f) Under ENABLE PPPOE, click the drop-down arrow and  
select YES.  
g) Under Authentication, enter the USERNAME and PASSWORD  
that were provided by your ISP. Username and password are  
often case-sensitive, so be sure to enter upper and lower case  
letters correctly.  
h) Under Settings, select the radio button labeled KEEPALIVE.This  
configures the phone to maintain the PPPoE connection even  
when your computer is idle or turned off.  
i) When the utility displays a window telling you it must reboot  
the phone, make sure your broadband modem is connected to  
your phone's WAN port, then click  
The UIP1868P is configured for use with Dynamic Host Configuration  
Protocol (DHCP) by default. If your broadband connection uses DHCP,  
simply connect your phone's WAN port to your broadband modem  
and then connect the phone’s power cord to an AC power outlet.  
Setting up with PPPoE  
If your broadband connection uses PPPoE, you will need to configure  
the UIP 1868P built-in router by inputting the user name and  
password provided by your Internet Service Provider. Follow the steps  
below to configure the UIP1868P to use a PPPoE-based connection.  
a) Connect a  
computer with a  
web browser  
directly to the LAN  
port of your  
OK.When the phone finishes  
rebooting, it will ask your  
broadband modem to assign an IP  
address. (See Figure #4)  
Figure #1  
Figure #4  
UIP1868P.  
(the default IP address of  
your UIP1868P) into the  
address bar of your web  
browser.Then press the  
Enter key. (See Figure #1)  
NOTE: For detailed installation with PPPoE, please refer to UIP1868P User Interface Guide – Setting  
up with PPPoE section)  
3 Setting up with a Static IP Address  
If your broadband provider has given you a static IP address, you will need  
to enter that information in the UIP1868P. Follow the steps below to  
configure the UIP1868P for use with a Static IP address.  
c) You should now see your  
Figure #2  
UIP1868P’s System  
Information Screen.  
Connect a computer with a web browser directly to the LAN port of  
(See Figure #2)  
your UIP1868P.  
d) In the menu bar down the left  
side of the screen, select WAN.  
e) In the menu bar on the top of  
the screen, select PPPoE.This  
opens the WAN PPPoE  
Configuration screen.  
Type http://192.168.15.1.  
(the default IP address of  
your UIP1868P) into the  
Figure #5  
address bar of your web  
browser.Then press the Enter key.  
(See Figure #5)  
(See Figure #3)  
You should now see your  
UIP1868P’s System Information  
Screen.  
Figure #3  
(See Figure #6)  
Figure #6  
 

Telex Video Game Headset PH 81 User Manual
The Singing Machine Karaoke Machine STVG888W User Manual
Toshiba Copier E STUDIO223 User Manual
Toshiba Power Supply G9 Series User Manual
TP Link Dishwasher TL SG1008 User Manual
TRENDnet Network Router TEW711BR User Manual
Uniden Telephone DSS8955 User Manual
Vanguard Managed Solutions Network Card 6500 PLUS User Manual
Vermont Casting Fan FCH CB2O User Manual
Visonik Home Security System MCT 501 User Manual